| |
FITRIA HELMIZA. SIMULASI VARIASI TEMPERATUR DAN KELAJUAN ALIRAN PENDINGIN MASUKAN TERHADAP DISTRIBUSI TEMPERATUR PADA TERAS REAKTOR TERMAL. Banda Aceh : Fakultas MIPA Universitas Syiah Kuala, 2020 |
|
AbstrakSimulasi terhadap distribusi temperatur dalam sebuah teras reaktor termal berjenis pressurized water reactor (pwr) ap1000 telah berhasil dilakukan. tujuan dari simulasi ini adalah untuk mempelajari bagaimana pengaruh kelajuan aliran dan temperatur pendingin masukan terhadap distribusi temperatur pada teras reaktor termal dalam kondisi transien. dari hasil simulasi diperoleh sebaran nilai temperatur tertinggi dan terendah di dalam teras. simulasi ini dilakukan menggunakan simflow 3.1 (free- version). teras reaktor dibagi menjadi 30 x 30 grid. hasil simulasi divalidasi dengan membandingkan eksperimen sederhana pada sebuah wadah aluminium dengan simulasi simflow 3.1. ukuran geometri bahan bakar merupakan pembesaran 10 kali dari ukuran sebenarnya. solver yang digunakan adalah chtmultiregionfoam yang dapat digunakan untuk kasus transien dan transfer panas. pada simulasi ini divariasikan kelajuan aliran pendingin yaitu 10 kg/s, 100 kg/s dan 14.300 kg/s dengan temperatur pendingin konstan
Baca Juga : STUDI EKSPERIMENTAL DAN PENYELESAIAN SECARA NUMERIK PADA PENGARUH PANJANG LALUAN TUBE TERHADAP UNJUK KERJA ALAT PENUKAR KALOR (Yufandi Azis, 2017) ,
Baca Juga : PENDUGAAN POLA DISTRIBUSI SUHU DENGAN TEKNIK BEDA HINGGA LAPANGAN GEOTERMAL JABOI, SABANG (NANDA GRISTINA, 2019) , 2,44 k dan variasi temperatur pendingin masukan yaitu 300 k, 552,44 k dan 1000 k dengan laju aliran konstan 10 kg/s. hasil yang didapatkan dari simulasi tersebut adalah pada variasi laju aliran pendingin terbesar 14.300 kg/s, temperatur pendingin bahan bakar naik menjadi 947,56 k. untuk variasi temperatur pendingin masukan 300 k, 552,44 k dan 1000 k temperatur bahan bakar mampu diturunkan berturut-turut sebesar 34 k, 26,09 k dan 13,77 k. penurunan temperatur bahan bakar semakin baik jika temperatur pendingin masukan rendah, namun setiap reaktor memiliki kondisi optimal tertentu. berdasarkan hasil simulasi dapat disimpulkan bahwa pemberian laju aliran dan temperatur pendingin terlalu besar menyebabkan distribusi temperatur di dalam teras menjadi lebih tinggi. kata kunci: simulasi, temperatur, kelajuan aliran, distribusi, reaktor termal simulations on the temperature distribution in a thermal reactor core type ap1000 pressurized water reactor (pwr) have been done. the purpose of this simulation is to study the influence of the coolant flowrate and the input coolant temperature to the temperature distribution in the thermal reactor core under transient conditions. from the simulation obtained the distribution of the highest and lowest temperature values in the core. this simulation is done using simflow 3.1 (free-version). the reactor core is divided into 30 x 30 grids. the simulation is validated by comparing a simple experiment on an aluminum container with the simulation by the simflow 3.1. the size of the fuel geometry is magnification 10 times the actual size. the solver used is chtmultiregionfoam which can be used for transient and heat transfer cases. in this simulation, the variation of coolant flowrate is 10 kg/s, 100 kg/s and 14,300 kg/s with a constant coolant temperature of 552.44 k and variations of the input coolant temperature are 300 k, 552.44 k and 1000 k with a constant flow rate 10 kg/s. the results obtained from these simulations are the greatest variations in the coolant flow rate of 14,300 kg/s, the fuel coolant temperature rises to 947.56 k. for variations in the input coolant temperature 300 k, 552.44 k and 1000 k the fuel temperature can be reduced by 34 k, 26.09 k and 13.77 k respectively. a decrease in fuel temperature is better if the input coolant temperature is low, but each reactor has certain optimal conditions. thus it can be concluded that the application of the flow rate and temperature of the coolant is too large causing the temperature distribution in the core to be higher. keywords: simulation, temperature, flowrate, distribution, thermal Pengarang tidak dapat memberikan Full Text secara langsung, untuk mendapatkan full text silahkan menghubungi email pengarang : fitriahelmizapipit98@gmail.com atau dapat mengisi Form LSS di bawah. Literature Searching ServiceTulisan yang relevan PENGARUH PERBANDINGAN VARIASI KOLEKTOR SURYA TIPE PLAT DATAR TERHADAP DISTRIBUSI TEMPERATUR (Kurniawan, 2018) ,SIMULASI CETAKAN (MOLDING) HOT PRESS DENGAN METODE ELEMEN HINGGA UNTUK PEMAKAIAN PADA PAPAN PARTIKEL (Qadri, 2015) , STUDI TEORITIS SISTEM PENDINGIN SIKLUS ABSORPSI AIR– LITIUM BROMIDA UNTUK APLIKASI COLD STORAGE DENGAN KAPASITAS LIMA TON IKAN (MUHAMMAD FARHAN, 2019) , |
|
|
Kembali ke halaman sebelumnya
Terkini
PROSPEK EKSPOR KOPI ARABIKA ORGANIK BERSERTIFIKAT DI KABUPATEN ACEH TENGAH |
ANALISIS KOMPARATIF TINGKAT PENDAPATAN USAHATANI PADI SAWAH IRIGASI DAN PADI SAWAH TADAH HUJAN BERDASARKAN STATUS PENGUASAAN LAHAN DI KECAMATAN KUTA COT GLIE KABUPATEN ACEH BESAR |
KAJIAN PEMASARAN DAN KEUNTUNGAN PETANI KACANG TANAH DI KECAMATAN DARUSSALAM KABUPATEN ACEH BESAR |
STUDI PENDAPATAN RUMAH TANGGA PERTANIAN DI DATARAN TINGGI (KASUS DESA URING KECAMATAN BUKIT KABUPATEN BENER MERIAH) |
ANALISIS PENDAPATAN USAHATANI TEMBAKAU DI KECAMATAN BANDAR BARU KABUPATEN PIDIE JAYA |